0

OEM/ODM Non-standard self-drilling screw Suppliers

Home / Products / DIY Outdoor Building Fasteners / Non-standard self-drilling screw
Non-standard self-drilling screw

Non-standard self-drilling screw

Non-standard self-drilling screws are specialized fasteners engineered with customized dimensions, thread patterns, and head geometries that deviate from international standards like DIN, ISO, or ANSI. These components integrate a drill-shaped point that enables simultaneous hole-drilling and thread-forming in a single operation, eliminating the need for pre-drilling in metals and heavy-duty plastics. By tailoring the drill point length and thread pitch to specific material thicknesses, these screws ensure optimal torque retention and structural integrity in specialized industrial assemblies where off-the-shelf hardware fails to meet tolerance or aesthetic requirements.
Inquiry Now Shopping Now
  • Non-standard self-drilling screw
  • Non-standard self-drilling screw
  • Non-standard self-drilling screw
  • Non-standard self-drilling screw
  • Non-standard self-drilling screw
  • Non-standard self-drilling screw
PREV：Cement expansion bolt​
NEXT：Flat head self-drilling screw
Non-Standard Fastening
#1 to #5 Drill Points

Non-Standard Self-Drilling Screws: Precision Engineering for Specialized Fastening

◆

Core Advantages

C1
Reduced Installation Cycle
Combines drilling, tapping, and fastening into one step, decreasing labor time and tool wear.
C2
Customized Load Distribution
Non-standard head diameters and shapes provide specific bearing surfaces to prevent material deformation or pull-through.
C3
Enhanced Material Compatibility
Optimized flute designs allow for efficient chip removal in non-ferrous alloys, reinforced polymers, or composite panels.
C4
Precision Fit
Custom shank lengths and unthreaded shoulders allow for exact clamping forces in multi-layered assemblies.

Technical Specifications and Features

Material Options
Carbon steel (1022A), Stainless steel (304, 316, 410), or Bi-metal.
Drill Point Geometry
Available in #1 to #5 points for varying steel thicknesses up to 12mm.
Surface Treatment
Zinc plating, Ruspert coating, Dacromet, or Ceramic coating for salt spray resistance.
Head Types
Modified truss, hex washer with integrated EPDM, countersunk, or custom architectural shapes.
Drive Systems
Torx, Security Pin, Square, or custom anti-tamper configurations.
●

Primary Application Scenarios

A01
Automotive Manufacturing
Securing interior trim or lightweight chassis components where standard spacing is restricted.
A02
Solar Energy Infrastructure
Fastening aluminum mounting brackets to thick-walled galvanized steel supports.
A03
Curtain Wall Systems
Architectural glazing where specific head profiles are required for flush finishes or thermal break isolation.
A04
HVAC Systems
Assembly of heavy-gauge ductwork and industrial cooling units requiring vibration-resistant threading.
G1

Torque and Speed Regulation

Effective installation requires an adjustable-clutch screw gun. Operating speeds should be calibrated based on the drill point size; higher RPMs are typically utilized for smaller diameter screws in thin gauge metal, while lower RPMs and higher pressure are necessary for #5 drill points penetrating thick structural steel to prevent point burnout.
G2

Storage Conditions

To maintain the integrity of the surface coating and prevent hydrogen embrittlement or surface oxidation, screws must be stored in a controlled environment with humidity levels below 60%. Avoid direct contact with corrosive chemicals or floor moisture. For bulk storage, ensure containers remain sealed to prevent dust accumulation in the drill flutes, which can impede drilling efficiency.
G3

Technical Considerations

  • Total Material Thickness: The length of the drill flute must exceed the total thickness of the materials being joined, including any gaps.
  • Electrochemical Corrosion: Ensure the screw coating is compatible with the substrate material (e.g., using stainless steel fasteners with aluminum to avoid galvanic reactions).
Drill point #1 to #5 Up to 12mm steel thickness Custom head geometries

Related Products

Zhejiang Donghe Machinery Technology Co., Ltd.

 

Zhejiang Donghe Machinery Technology Co., Ltd. offer Wholesale Non-standard self-drilling screw Manufacturers. Our company passed the ISO9001:2000 quality management certification system standard in 2017 and is an enterprise with self-operating import and export rights.
Our company produces various international industrial standard products, including Chinese GB standards, German DIN standards, American ANSI standards, British B standards, and so on. In addition, our company can customize various non-standard fasteners according to customer requirements. The products are exported to Europe, Australia, Africa, the United States, and other regions. We always provide customers with good product and technical support, and sound after-sales service.

News

Factory Show

Factory appearance
Intelligent packaging
Quenching furnace
Fastener supporting mold workshop​
Cold heading workshop
Pragmatic​
Innovation
Sincerity
Laboratory
Fully inspected products using optical sorting technology​
Office environment​
Enterprise Honorary Certificates​

Contact Us

Please complete the form below and one of our team will get back to you as soon as possible.